Patrick Pryor Killed in San Diego MTS Substation Accident
Patrick Pryor, an MTS Electromechanic With Two Decades on the Job, Dies After a Reported 12,000-Volt Exposure at a Rail Substation
SAN DIEGO, CALIFORNIA (November 22, 2026) – A longtime San Diego Metropolitan Transit System worker identified as Patrick Pryor was killed in an electrical accident at an MTS substation in San Diego.
San Diego County officials are saying that the electrical injury occurred on Friday, November 13, though the exact time has not been released. Patrick Pryor was working at one of the agency’s rail substations when he suffered serious electrical injuries for reasons that have not yet been determined, according to FOX 5/KUSI.
A friend told the station the incident happened at the 33rd and K Street substation and that Pryor was exposed to roughly 12,000 volts. Coworkers immediately tried to help him, and emergency responders were called to the scene.
Despite the efforts of coworkers, paramedics, and hospital staff, Patrick Pryor died near midnight, surrounded by loved ones, according to MTS CEO Sharon Cooney. Cooney told staff that the cause of the accident has not yet been determined.
Pryor joined MTS in 2006, became a journeyman Wayside Electromechanic in 2011, and worked in the rail Maintenance of Way department, where he trained and mentored apprentices. A friend described him as calm and dependable and said his death was likely the first fatality of its kind in the department.
State investigators have studied deaths like this one before. A California FACE report examined the 1994 death of a 42-year-old traction power inspector for a public transportation company who was electrocuted by a 17,000-volt feed line during routine maintenance at a substation.
Cal/OSHA is now looking into Pryor’s death, and state rules require that electrical equipment be treated as energized until it is tested or otherwise proven to be de-energized. That raises questions about which circuits were live that day, what testing took place, and what safeguards stood between workers and the energized equipment.
Liability for San Diego Substation Electrical Accidents
Work on high-voltage equipment is governed by some of the most detailed safety rules in California. Cal/OSHA’s High-Voltage Electrical Safety Orders require that only qualified electrical workers handle energized conductors or equipment and that employees be trained in the work practices those orders require. Another provision, section 2940.1, requires that all electrical equipment be treated as energized until tested and that operating voltage be determined before anyone works on or near energized parts. When a worker is hurt on the job, the employer’s responsibilities are largely defined by state workplace laws, but outside parties such as contractors, equipment manufacturers, and maintenance firms can face separate negligence claims. The key questions in these cases usually involve the following:
- De-energizing:Â Lines and equipment must be properly isolated, tested, and grounded before workers treat them as safe to touch.
- Lockout Procedures:Â Switches and breakers should be locked and tagged so no one can re-energize a circuit while work is underway.
- Qualified Workers:Â Only trained and qualified electrical workers should work on or near energized high-voltage equipment.
- Protective Equipment:Â Insulating gloves, sleeves, and tools rated for the voltage involved must be provided, inspected, and used.
- Equipment Condition:Â Defective switches, breakers, or insulation can expose workers to hazards even when procedures are followed.
Courts have confirmed that these safety rules carry weight beyond regulatory citations. In Elsner v. Uveges (2004), the Supreme Court of California addressed a lawsuit by a roofer who was hurt when a temporary wood plank scaffold collapsed beneath him and who sued the project’s general contractor rather than his own employer. The court held that, under 1999 amendments to Labor Code section 6304.5, Cal/OSHA provisions can be used to establish a duty or standard of care in negligence suits against third parties, not just employers. Because the amendments did not apply to that earlier accident, the plaintiff’s verdict was reversed, but the rule the court recognized governs cases today. As a result, the same regulations that control high-voltage work can be used to measure whether a contractor, manufacturer, or other outside party acted reasonably.
Preventing Electrical Deaths at Work
Electricity remains one of the deadliest hazards in the American workplace. According to the Bureau of Labor Statistics, 142 workers died from exposure to electricity in 2023, and 130 died in 2024. The Electrical Safety Foundation reports a total of 1,940 workplace fatalities involving electricity between 2011 and 2023. Many of these deaths are preventable through well-established practices. Employers that take electrical safety seriously typically focus on:
- Job Briefings:Â Crews should review hazards, voltages, and the work plan before every task, especially when conditions change.
- Voltage Testing:Â Workers should verify the absence of voltage with properly rated testers rather than relying on switch positions or labels.
- Grounding:Â Temporary protective grounds help protect workers if a line is accidentally re-energized.
- Approach Distances: Workers must keep minimum distances from exposed energized parts based on the voltage involved.
- Supervision:Â Experienced oversight and clear communication between system operators and field crews help prevent mistaken switching.
The high-voltage systems that power transit networks, factories, and utilities depend on workers who accept real risk every day to keep them running. Those workers deserve employers and contractors who follow every safety rule, provide proper equipment, and never cut corners to keep schedules moving. When someone is killed on the job, independent investigations by agencies like Cal/OSHA play an important role in identifying what went wrong. Families have the right to learn those findings and to understand whether any party failed to meet its legal duties. They may also hold outside contractors, manufacturers, or other third parties accountable when negligence contributed to a death.
Investigating Workplace Electrical Accidents in San Diego
We at Feher Law offer our heartfelt condolences to the family, friends, and coworkers of Patrick Pryor. We hope the investigation brings accountability and leads to changes that protect every worker who maintains high-voltage equipment. His death raises serious safety concerns for transit and utility workers throughout the region. What safeguards were in place at the substation that day, and did they work as intended?
Have you or a loved one been affected by a workplace electrical accident in San Diego or elsewhere in San Diego County? The law limits how employers and contractors may expose workers to high-voltage hazards, and families can hold negligent parties responsible. When a public agency runs the worksite, it typically controls the switching logs, maintenance records, and training files that show how events unfolded. Our team of safety advocates and accident investigators can help you understand what happened, from equipment inspection reports and maintenance history to coworker accounts and Cal/OSHA findings. If you have questions about your rights or would like a free, independent investigation, we’re here for you anytime at (424) 433-4412.


